Ability to Delete Previous Jobs from the Dashboard
@kirkatude wrote: It would be helpful to be able to have the ability to delete previous jobs from the Dashboard. Now, one has to do each one, one at a time, on the printer itself. Kirk Posts: 1...
View ArticleFDA Compliance in 3D Printing
@yoderkl wrote: I came across this article yesterday: http://www.materialise.com/en/press-releases/materialise-first-company-to-receive-fda-clearance-for-diagnostic-3d-printed To save you the trouble,...
View ArticleQuale resina ha caratteristiche ESD? o simili
@Demosystem wrote: quale resina ha caratteristiche ESD? o simili? Grazie! Posts: 1 Participants: 1 Read full topic
View ArticleWho is actually using a distiller for used IPA?
@Walter_Gillespie wrote: I produce a large quantity of used IPA and will be doubling that use by July this year. Trouble is I’ve found no good way to dispose of this used, contaminated IPA. I’ve...
View ArticlePrint Errors
@DPC wrote: Hey hii I am using form2 printer. from past one year. All of sudden my printer started showing lot of print errors like Not able to print holes for mechanical components which are 4mm...
View ArticleClik here to view.
Going to grind resin scrap and reuse it
@Walter_Gillespie wrote: Yes, I will start grinding the used support base and support scrap into a powder that will be used in our resin castings as a filler. Better than throwing it in the trash. If...
View ArticleSupport dots
@Tbird wrote: Just my form 2 few days back After removing the support The support dots are like so big in white popping out, I did clip them one by one at the edge gently, Anything wrong I’m doing...
View Article3shape splint designer
@Rendres wrote: Anyone have experience with 3shape splint designer. Can’t seem to get a good fit with the dental LT resin. Been tweaking the inside offset but still too snug on the demos. Any tips?...
View ArticleHelp! FormWashCureUpdater just Bricked my brand new Form Wash!
@AZideaworks wrote: Less than a few days old, I decided to update the firmware on the Wash, since apparently there are quite a few fixes in the latest patch. I first plugged in the wash to my USB and...
View ArticleBrand new Form II can't see one of my new resin cartridges; Help!
@AZideaworks wrote: Hey there, I’ve got a brand new machine… I bought two units of Gray resin, and one of those two refuses to register when I press it in place. I’ve checked the contacts on the...
View Article3D - Mouse dos not work
@Andreas wrote: Since the latest update the 3D-Mouse dosn´t work. The mouse is from 3D-Connexions. Any sugestions? Thank you. Posts: 3 Participants: 3 Read full topic
View ArticleAny cheap or DIY device for stirring?
@garjor wrote: There is the Nextdent LC-3DMixer. Is there any other or an idea for DIY? TIA Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Preform needs to clean up after itself in the Control Panel
@mjncad wrote: Why doesn’t Preform clean up after itself once an update is installed. Are these phantom entries in my Control Panel, or what? Capture.PNG991x551 53.3 KB Posts: 3 Participants: 2 Read...
View ArticleClik here to view.
Bad Foaming with Grey V4
@Rhodes69 wrote: Just bought a Form2 last week, had good luck on two small 3 hour prints. The third print was 6 hours and I it was CRAP!! What is up with the Grey V4 resin? I have firmware...
View ArticleWhat do I do when the platform sticks to the tank?
@jmwright1058 wrote: I’m printing the Formlabs Test Print.form After printing a few layers successfully (I think), it prints the next layer, then begins the peel process. The tank pulls downward...
View ArticleColor Kit with Engineering Resins
@HotLoli wrote: Greetings, Have anyone tried mixing the color kit with Engineering Resins such as the Tough or Durable resins? The standard resins are too brittle for the product prototypes i’m...
View ArticleRepair castable resin print?
@kim_lunn wrote: I broke the shank of a ring that I printed with castable resin. Is there something I can use to “glue” it back together that will burn off in the kiln? Posts: 2 Participants: 2 Read...
View ArticleClik here to view.
Trouble with my printed file
@ThibautSa wrote: Hello everyone ! I have a big problem with my print: Here is the file with the printing specifications: 2018-04-03_10-57-48.png977x823 280 KB Either it doesn’t stick well to the...
View ArticleFormalbs material specs
@NickieTwyford01 wrote: We are currently experiencing some issues with a few jigs that we use within an environmental oven. During testing the oven is set at 50 degrees Celsius and the the jig is...
View ArticleAny resin suggestions for parts that can hold up in cold temps?
@Richard_Beck wrote: I did some searching without luck and don’t see it in data sheets. I called customer support and was told they have not done any testing for low temps. Based on that, I throw this...
View Article