Form1+ Preform 2.11.0 prints nothing with version 2 clear 25µ
@KenCitron wrote: I just updated my Preform to 2.11.0 and tried to print a model at 25µ with clear #2 and ended up with a slight blob at the bottom of my tank, really under exposed. Previous version...
View ArticleClik here to view.
March for science button
@Barnhatt wrote: Gearing up for the Seattle March for science means my form 2 is busy making 3d printed buttons to wear. what does everyone think? Posts: 3 Participants: 2 Read full topic
View ArticleForm 2 V-3 Resin Tank Life.... 2 Liters or More?
@RetXpres wrote: We are printing Dental Models @ 100 Microns on our Form 2. We are very cautious of placement using heat maps. Could we expect to get more than 2 Liters of Resin on one tank? I have...
View ArticleExcessive layer print time
@tamirlance wrote: Hi All, Newbie here. I'm trying to print my first part and the printer is taking several minutes between layers. Is that normal? The videos online (non-timelapse obviously) show the...
View ArticleForm1 Resin tank dry?
@Scote wrote: Is it ok to let the resin tank dry? I use to remove my resin when I finish a print.. because my first tank start to get so .. dont know how to sya it.. chimical hole in the silicone?...
View ArticleAdding resin mid-print
@Digitalsmithy wrote: Hello. My printer has notified me I may not have enough resin to finish the job that I'm about to start (I'm pretty sure it does) and it directed to the help section here where...
View ArticleCatridge stuck?
@Digitalsmithy wrote: Hello all. I went to replace the cartridge today for the first time and it seems to be stuck. It slides about half way out then gets "caught" on something. As far as I could tell...
View ArticleHow do you know when the Resin Cartridge is Really Empty?
@RetXpres wrote: We keep getting notifications that the Resin Cartridge is Empty and it really is not. So my question is how do you really know that it is really empty? There should be some kind of...
View ArticleBrand new printer, Motor jammed and "in use by another instance of preform"
@jlabscreative wrote: I bout my printer over the holidays but was unable to open the box until today. I have several issues: The first time I plugged in the printer I hear a very disconcerting...
View ArticlePrinter busy error while transfer
@akhot wrote: not able transfer job from preform to printer,preform not detecting my printer stating "printer is busy unable for printing" Posts: 2 Participants: 2 Read full topic
View ArticleForm1 FEP based resin tray prototype
@HTL wrote: The link below points to some photos of a FEP based resin tray for the Form 1/1+ that I may be offering at flexvat.com provided further testing of the vat pans out. The photos are of a...
View ArticleInterlocking Parts on Form 2?
@chris_ell wrote: Hey gang. So here's a dumb question: is the Form 2 able to print interlocking parts in one go? I'm thinking about trying this Pangolin as a test...
View ArticleFinishing Castable resin prints and bad prints
@Selkirk wrote: Hi. we have recently purchased a Formlabs 2 for our college jewelry program and I am trying to figure out some issues.Main problem is that the prints have a roughness to them..almost...
View ArticleClik here to view.
What causes these print imperfections?
@BRCHNdesignhouse wrote: I'm pretty new to the Form 2 and could use some advise on sorting out these issues. First, I get a few random holes in some prints. I'm quite sure the glass and resin tray are...
View ArticleForm1+ sale - AUSTRALIA- Brisbane _ 1200$
@Eder_Lima wrote: Hi I salling my print, it had a issue but still print. Posts: 1 Participants: 1 Read full topic
View ArticleFormlabs support
@selena wrote: How have people found the support response? It has been 48 hours since I responded to the initial response and provided pictures and details of failed prints and I have yet to have any...
View ArticleClik here to view.
Resin Sensor Error
@LabCir wrote: IMG_0150novo.jpg2448x3264 736 KB All site procedures have been done. I can not use the machine.Has anyone ever solved this problem? Posts: 2 Participants: 2 Read full topic
View ArticleUpdating
@grogbro wrote: Everytime it says I need an update. I hit download and it just goes away and closes the program. Then, I reopen PreForm and it opens fine with no update message. Then, when I use it...
View ArticlePart doesn't stick to te platform
@Ing3nia wrote: Hello! Yesterday evening I was printing some pieces that I needed, when I was going to print the final model I started to hear a "click" in the peeling process, I noticed that the...
View ArticlePreForm complains model needs repair, but it doesn't actually need repair
@Randy_Cohen wrote: Seen this behavior a few times over the last week or so. I'll load a model in to PreForm and it'll pop up the dialog about needing to repair the model (even though I've run it...
View Article