Clik here to view.
Experimenting with Expired Resin
@Richard_Kagerer wrote: I'm curious what kind of real-world shelf life folks have been getting out of their resin, and what sort of luck you've had extending the working life past the expiry date....
View ArticleFor how long is it safe to pause a print?
@Richard_Kagerer wrote: I noticed while a print is paused, the machine still makes noise (which I assume comes from the tank heater and possibly whirring of other internals). Sometimes I want to demo...
View ArticlePost cure waterbaths
@Tit_Inn_Des wrote: I read that you can post cure in the uv chamber, flexible parts in a water bath. Can you do this with all resins? Posts: 1 Participants: 1 Read full topic
View ArticleAdding Heat to UV Cure
@jfishman wrote: I'm looking for a way to add heat to my UV curing set up. I currently use the $30 nail salon setup (so there's no real heatin the mix).... I'm looking for input on this idea I have:...
View ArticleClik here to view.
Recoating the Tanks with Sylgard
@Dudemeister wrote: For the past year or so, I put aside all the used tanks from my Form 1+, and even bought a few used ones for a cheap. This past week I finally got with the program, and bought a...
View ArticleWhat do you think about this rasin?
@orthoniv wrote: http://nextdent.com/products/ortho-clear/ Posts: 1 Participants: 1 Read full topic
View ArticleClear Resin Post Print Turning White
@vincentsiu8899 wrote: So once I finish my 3d prints, and the IPA rinse, all of my clear prints start turning white almost immediately, how can I prevent this, and keep it clear? Posts: 2...
View ArticleIncreasing durability
@CaptainBisquick wrote: My print is an electronics device enclosure and I'd like to increase the abrasion resistance. I'm wondering if I should coat my print (either black or white resin) with a clear...
View ArticleClik here to view.
Hole in edges
@gaelp wrote: thumbnail_IMG_20170213_145245.jpg960x1280 94.6 KB Hello, I have a question, when I print a case, there are some hole like the picture. Someone can help me for this problem ? Posts: 5...
View ArticleFlexible resin airtight?
@jojoran12 wrote: Hello, I'm wondering if the Flexible resin products are airthight, and if they can be used as custom seals. Posts: 1 Participants: 1 Read full topic
View ArticleForm X Ceramic resin
@Leonardo_Tuorto wrote: Anyone tested the ceramic resin by form x? It is similar to tethon 3D ceramic resin? Posts: 1 Participants: 1 Read full topic
View ArticlePrint failed form 2
@vincentsiu8899 wrote: My print failed, resin got everywhere in and out of printer, pieces of the print fell into the tank, and bottom of resin tank is all gritty, what do I do? Posts: 2 Participants:...
View ArticleWarning that build platform is missing
@csauve wrote: It would be great if there was a warning signal or something letting you know that the build platform isn't installed or not completely installed. Twice now I've started a print not...
View ArticleAutoclaving: Std Clear vs High-Temp
@DavidParis wrote: Autoclaved two samples from FormLabs; one in Standard Clear, and one in High-Temp (clear). They both stood up extremely well, with the Standard Resin slightly yellowing, and the...
View ArticleClik here to view.
First Print: Purity Seal War Hammer 40K Prop
@JetBlaque wrote: Hello all, this is my first post and my first print. I was asked to create something based on a "Purity Seal" from the popular table top game "Warhammer 40k". I learned a lot on this...
View ArticleClik here to view.
Valentine's Day Gift
@DigArt wrote: Hi all you lovers out there. This might be a bit late but if you'd like to print a set of interlocking hearts here is a design I created for my sweet heart. image.jpg828x646 123 KB Form...
View ArticleClik here to view.
Form 2, printer cancelled print, and now table is buried inside resin tray
@Tit_Inn_Des wrote: The printer automatically cancelled a job, with the table buried inside the resin tray. Now I have no idea how to pull up out of the resin tray. Please help, as I do not want to...
View ArticleWorking with "Out of Resin Error"
@DigArt wrote: What is the typical method for using up the last bit of a bottle of resin? I have 1.5 cups (approximately 300 ml) of resin left. I filtered it and poured it back into the bottle....
View ArticleLow resin error?
@vincentsiu8899 wrote: I've printed about 500 ml with my black resin with my form 2, but my printer gave me a low resin message, is this an error, or was there some mistake with how much resin I got...
View ArticleDo LED's affect the resin?
@vincentsiu8899 wrote: I was thinking of adding LED strips along the bottom portion of the cover of my form 2 in order to light it up a little bit, would adding these LED's affect the resin or...
View Article