Curing Solution
@danjep wrote: I still see so many questions about curing boxes. I posted this earlier but it bears repeating. Go to Ebay and search "dry heat sterilizer" there are several but there is one for less...
View ArticleJoining Tough Resin part ro a High Yemp resin part
@Gordon_Brand wrote: Hi Guys, I have a prototyping project that requires a high temperature plastic to withstand hot air at 110° (hairdryer) but also have a snap fit for repeated attachement to the...
View ArticleNew Form 2 Print Problems
@DrZ123 wrote: I am a dentist and just got a new form 2 last week for dental model printing. Right away I printed a few models in one shot using the grey resin I got and had great results. Since the...
View ArticleClik here to view.
10 floors building, scale 1:87, model railway
@Ole_Vedel wrote: My latest project, scale 1:87, model railwayFor a 10 floors building, I needed 40 pieces. balconies, and a large amount of stairs.The rest of the building is made on my cnc milling...
View ArticlePart getting cured in resin tank instead of getting printed in the build...
@kart2020 wrote: Hello Friends, I am new to SLA printing and formlabs. My first print came fine, but when I try printing the second model, nothing was printed in the build platform. Instead, I was...
View ArticleClik here to view.
Impressão de anel!
@rodrigo_antonio wrote: Ola a todo estou reparando uma sobreposição de camadas no aro na parte de baixo do anel já fiz a orientação de outras formas mais o problema pediste alguém já teve algo...
View ArticleFlask orientation for burnout?
@arthurr43 wrote: Hopefully getting my form2 by next week! I have read that when casting resins you should put the button face up since the resins does not actually melt, Thoughts? any help is much...
View ArticleClik here to view.
Resin Filter Funnel
@DigArt wrote: My method for keeping the resin tank clean is to filter the resin with a disposable paint filter funnel. Unfortunately the funnel could not be left unattended because it would sink to...
View ArticleClik here to view.
Specific Gravity of Castable Resin for Jewelry
@katkramer wrote: Hey guys, I had just created a chart from the information in another thread where we were discussing the specific gravity of castable resins. Looks like Luke had replied to one of...
View ArticleError 1065
@Cristobal wrote: hi anyone can help me pls i buy a form2 and download and install last version of firmware : rc-1.11.7-62 but now when sending a job my mac show me you have error 1065 help pls Thx 1...
View ArticleClik here to view.
Tapered Pillar Supports?
@3DTOPO wrote: I have seen several instances of people sharing images that have tapered pillar supports. For instance the PreForm screenshots in this thread. According to the Release Note log, it was...
View ArticleClik here to view.
Defective Print Cartridge
@KevinHolmes wrote: Just noticed print stopped with error that print cartridge "appears to be empty" - but it's brand new cartridge on it's first print, less than 20 layers in. Obviously that focused...
View ArticlePrinter issues
@campingtomz wrote: hello everyone so I recently acquired a form 1+ from a individual. this thing was a mess like just meh. resin spilled everywhere it needed a lot of TLC. what the previous owner had...
View ArticleClik here to view.
Creature 3D Print
@chulev wrote: Hello all, I did a print of a Creature that was sculpted in Zbrush as part of Gio's Master Class and based on concept from Carlos Huante. It is 7.5 inch tall/19cm.Just wanted to share...
View ArticleCan high temp resin be used as mold for cast pewter?
@silvertek wrote: Wondering if anyone has tried to make a direct casting mold for pewter using Formlabs high temp resin? Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Z-banding
@lukepighetti wrote: Any thoughts on how to improve Z-banding on this brand new (Amazon) Form 1+? This happens at the same level on all prints. Prints appear to be good otherwise. 2016-12-24 10.42.46...
View ArticleForm 1+ updating
@lukepighetti wrote: Hello all, I'm having weird things going on trying to update my Form 1+ in OpenFL 2.3.3 Should I update in PreForm 2.9.1 and then go back to using OpenFL 2.3.3? Posts: 2...
View ArticleWhat happen to FLGPCL03?
@SonKim wrote: When I bought my Form2 I picked the clear resin(FLGPCLO2) to go along with it, which is okay but it turns slightly yellow. I heard about FLGPCL03 which is slightly blue/grey, but I...
View ArticleX-axis making noise after skipping steps
@fantasy2 wrote: I've printed some very large tough resin parts. Near layer 14(end of the base), the X-axis(for peeling) started skipping some steps with loud bang noises. Same for the Z-axis. Both...
View ArticleClik here to view.
Parts are not printing well all of a sudden
@Ken_Weiland wrote: Up until a few days ago, I have been getting pretty decent prints in 50 and 100 microns. I tried 25M and had some failures, so switched back to 50M . Now I'm seeing some strange...
View Article