What's the oldest resin you've used?
@piGuy wrote: I completed a print yesterday on my Form 2 using Tough V1 that had a mfg date of Oct 26, 2015. The print turned out great despite the resin being 2.5 years old. I suspect Formlabs is...
View ArticleShutdown Form2 and FormCure
@InProdukt wrote: He there, I start this day with my Form2 and my FormCure. So I think I have a “problem”. When the print job is finished than I can’t shutdown the two machines. There is no switch key...
View ArticleMissing LT resin tank message
@mjncad wrote: After each and every print I have to jiggle the tank to clear the ‘missing tank’ error message with my new LT tank. I have no idea if it’s just the tank, or firmware updates, or a...
View ArticleForm 2 for sale in Belgium 2500 EUR
@SofiaApostolo wrote: I have a Form 2 for sale in Belgium. Not sure exactly how old as it was given as a replacement for the printer I initially bought. I have it since September last year and it has...
View ArticleClik here to view.
Foam in resin tank
@Resindustkits wrote: I read in a previous thread about foam in the resin tank. I’ve had alllot of foam building up using grey resin. Ive only done eight prints but the last one has pin holes on the...
View ArticleClik here to view.
Editing supports
@Resindustkits wrote: After using auto generate function. I always have to go in and edit the unsupported areas. Shades of red have always showed up, but in the last one red lines also showed. Why did...
View ArticleAlternative Support to Model Interface
@David_Persuhn wrote: I have a suggestion for a slightly different support to model connection point. The existing design places the most narrow point directly at the interface of the model surface....
View ArticleClik here to view.
Rough gloppy prints
@jbrown wrote: I have been having an issue with prints coming out very grainy or gloppy. I have cleaned the optics windows, filtered the resin and even replaced the tray. I am at a loss. This is...
View ArticleI have a question !!
@johnwicky wrote: Hello I have a small problem with the curing of the epoxy resin. I have a few geckos printed, these have a hole in the stomach where a magnet should go in. But more on that later....
View ArticleAre Form+1s still viable and if so
@JetBlaque wrote: …for how long? I have a person wanting to sell me a form +1 and I’m thinking of buying it cuz it’s such a screaming deal. I already have a Form2 but I dont think I can pass this +1...
View Article料不足是怎么回事？
@Anice wrote: 这有一台form打印机打印时总会自动停机，显示料不足，需要把料重装一次才能继续打，平均一小时左右就会出现一次这种故障，这个该如何维修？ Posts: 1 Participants: 1 Read full topic
View ArticleStandard Black resin is rubbery and wont seem to harden
@tonberryhunter wrote: I did a couple of prints in the last couple hours with a new tank of Black standard Form 2 resin and both prints are rubbery. Hard but rubber like. The supports are almost...
View ArticleBest Primer?
@Spikes007 wrote: I printed several things with very small details (skin Pores and veins) my question is what is the best primer to use to conserve and bring out those tiny details? thanks Posts: 5...
View ArticleBest way to print thin walls?
@dcapua wrote: Hey guys, I am having difficulty printing a part with thin (300 um) walls with the same distance between each wall. For some reason I was able to do this on the Form 1+ but not the Form...
View ArticleUpdate On-Machine Job with Actual Print Time
@David_Persuhn wrote: After a job prints, it would be nice if the estimated print time that is shown on the machine could be updated to use the actual print time. This way, re-running a job from the...
View ArticleGrey vs Grey Pro detail comparison
@andyfilms wrote: Hey all! I’m a prop builder. I’ve been using Grey resin a lot to create a master model which I can then mold and cast to make many copies. Unfortunately, regular Grey resin is too...
View ArticleAutomated Reboot
@faufablab wrote: Hello, because of our network Installation we are forced to reboot our Form2 everyday to keep connected to the dashboard and won’t loose connection. Wouldn’t it be great to set a...
View ArticleLoose fitting dies for dental models
@SDTech wrote: Hi everyone we are printing dental models with detachable dies. the first few prints we did came out great the dies fit perfectly. The last two prints we did the dies are super loose,...
View ArticleWhat type of Casting Investment for Castable Resin?
@Selkirk wrote: Hi. I am writing on behalf of a jewelry instructor so forgive me if I get the terminology incorrect. She has been told that the Gypsum investment that we have is not compatible with...
View ArticleReusable mold material
@KenCitron wrote: I have used remelt from Alumilte but came across the same thing probably from the manufacturer called composimold found here: http://composimoldstore.com They also have a putty but I...
View Article