Clik here to view.
1st one turned out great, rest not so much
@Roswitha_Sch973 wrote: hey guys, i have my form2 now since it came out. 99% of the time i'm very happy with it and if something goes wrong it was always my fault but i always could fix/change it. but...
View ArticlePost print pre-process storage
@asaxena76 wrote: Hi Community members, I was wondering if there is a way to delay the post processing steps ( IPA bath etc) after the print is complete and taken out of the printer. Essentially , I...
View ArticleQuestions from ortho lab tech thinking of purchasing Form 2 for dental models
@nate wrote: I am a small one-man dental lab that fabricates orthodontic appliances. I am thinking of buying the Form 2 to print dental models to be used for appliance fabrication purposes. For those...
View ArticleDowngrading firmware of Form 2 to use Open mode with wiper and heater
@Raland wrote: Hi everyone! Is it possible to downgrade firmware of the printer to use wiper and heater? What version of firmware shoud I use and where I can get it? Regards. Posts: 2 Participants: 2...
View ArticleHow many ABS parts can I produce with Galomb on Form2- printed molds in...
@dmyegorov wrote: Liked the article https://formlabs.com/blog/3d-printing-for-injection-molding/ What is the longivity of the inserts? Lets say i print them with a high temp resin and use the ABS...
View ArticleClik here to view.
Problem with print cracking around supports
@thowe26 wrote: Printed the following using Standard grey resin at 25 and 50 micron with the same result, the print "cracks" at the point a few supports touch.The supports in Preform are point size...
View ArticleUse Form1+ resin in Form2
@jpt000 wrote: Hello all,I have a bottle of clear resin for Form1/1+ unopened. Can I use it in the Form2? Can I just refill the resin tank with it and carry on printing?Thanks! J Posts: 4...
View ArticleClik here to view.
Nixies print Log
@Nixie wrote: Hello guys, I've had my Form 2 for 2 days now and wow! I think its actually better than I had expected! Rather than make a new post every time I print something, I will just add to this...
View ArticleNew grey 3 : very brittle
@oberst3221 wrote: I'm already missing the old Grey 2. The mild flexibility made printing long thin parts viable. The new Grey 3 is far dryer and brittle. I've seen quite a few thin parts snap apart...
View ArticleLooking for a Form 2 (North America)
@Revocrete wrote: As the title says, I am looking for a New or Used Form 2 in North America, more specifically in Ottawa, Ontario. Please contact me if you have a printer in mint condition for sale....
View ArticleClik here to view.
From VR to reality
@MiguelGuerrero wrote: Here's a little mechTank I made in Oculus Medium and printed with the form2. I will be printing a large one soon once I get some time to key the legs out....
View ArticleStrange noise and no resin cured on platform, just in tank
@SFernandez wrote: Monday I was printing without any problem, but yesterday when try to print a big noise starts, I put a video because I cannot explain.The platform didn't adhiere anything and the...
View ArticleB9 Yellow Resin - Failing
@Nielsvandooren wrote: Hi all, I've recently bought a B9 model cure unit from B9creations. Decided to also order a 1L of their castable resin for some experimenting. (Normally I print using Formlabs...
View ArticleMultiprinter Upload and Fleet Management
@gaud_complex wrote: Hello, I currently own two Form 2s and provide printing on 3D Hubs. In the near future I'm looking to add more Form 2s and, although not currently an issue, the individual nature...
View ArticleEconomy resin for jig making
@KenCitron wrote: I would like to see a cheap resin that can handle med to low detail for making jigs, gadgets and suitable for rtv mold making. Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Reduce base area to speed up builds
@bee wrote: Good afternoon,I was wondering if there is a way with the form 2 to reduce the area of the base? sample test.jpg1152x766 154 KB I have a sample part shown that has a giant base. I was...
View ArticleClik here to view.
Cant upgrade printer firmware!
@dunginhawk wrote: So I am just getting around to testing grey v3 and I cant Preform is 2.10.0but printer is 1.11.8 I plug in the printer to my laptop (current machine) and it says FW is up to date....
View ArticleFinancing
@cdavenport wrote: I learned of Formlabs via Facebook. Since the company advertises to "Joe the Plumber" therein, one might reasonably expect the availability of a financing plan. It's not a used car,...
View ArticleClik here to view.
Distiling IPA (alcohol) between uses - recycle
@peterstern wrote: I got tired of spending big bucks on IPA, yet using dirty IPA and getting sticky prints, so I decided to try using a water distiller to recycle the dirty IPA on a regular basis....
View ArticlePreform Software - Print Measurements
@philcox wrote: Hi All, I just received my Form 2 today and I'm still getting to grips with Preform, one thing that I haven't been able to find in the software is a way to determine how large a model...
View Article