Clik here to view.
Desk clock with support structures
@Ch1 wrote: VW Typ3 Oldtimer Clock turned to desk clock. 26180315_178585262887938_8596070558372724736_n.jpg1080x1080 Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Idea medical flashlight
@Ch1 wrote: I like to build an medical flashlight. Here some Highlights: adjustable colour temperature, colour rendering more than Ra>95, IP67 Waterproof Touch control, Hygienic clean design....
View ArticleForm Wash - Motor Jammed
@HBDDAC wrote: When the basket moves down or up it gets stuck midway and makes a horrible noise like something is stuck. There is no obstruction I can see at all. Any suggestions? Posts: 1...
View ArticleTOUGH resin finishing tips needed
@Olivier_Suire wrote: Hi ! I have essentially two types of issues with “TOUHG” resin finishing. The cleaning is pretty darn difficult, but I might fix that by purchasing yet more IPA and rinse in...
View ArticleNew Black V4 vs. V3
@JohnK42 wrote: A new Black V4 seems to be released. What are the main differences compared with the old V3? Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Can't access Store
@Numity wrote: Hello, about yesterday and today, I can not access the store to buy the new resin and other accessories, and even the HelpBot doesn’t show up too. I live in Vietnam and when I change...
View ArticleClear resin v2 and v4
@xnUMb wrote: Hi there, Last time I ordered clear resin I also ordered a new tank. I got clear resin V2 so the tank became clear resin V2. I ordered a new liter of resin and they send a clear resin...
View ArticleClik here to view.
Help impossible print with dental model
@NuovaEliodent wrote: Hello to everyone, I’m dental tecnichian, I’m starting printing model in my lab with Form2 with dental model resin; my first four or five print was succesfuly but now I have a...
View ArticleClik here to view.
Corner of raft peeling off build platform during print
@rkagerer wrote: My latest Form 1+ print started to peel off the build platform in one corner: This print was done with a fine tuning setting to lower the build platform 0.5mm. Should I be concerned,...
View ArticleClik here to view.
Flashing on prints
@mikegerwig wrote: This “flashing” just started showing up on my prints. New bottle of material. The previous half dozen or so of prints were doing fine, then this started showing up on the prints....
View ArticlePhotocentric3D UV Resin
@awieneke wrote: Hello, since i use the cartable V2 from formlabs, the castingcompanie has problems. it will not burn out correctly. Now i have the idea to try “Photocentric3D UV Laser Gussfähiges...
View ArticleHow long is "too long" for build time?
@abreverman wrote: I know that some printers (specifically FDM and DMLS) have recommendations to limit the build time to ensure that the printer head does not overheat. There are obviously some...
View ArticleHow long is "too long" for a build time?
@abreverman wrote: I know that some printers (specifically FDM and DMLS) have recommendations to limit the build time to ensure that the printer head does not overheat. There are obviously some...
View ArticleResin Sensing Error! Part 3
@SeanDBrown wrote: SO I am back with yet another printer (2nd one) and a hand full of Resin Sensor Errors! I have cleaned, tightened, wiped, replaced as much as I can on this (New) printer and get...
View ArticleSolved - Preform Launch Issue
@DerekMurphy wrote: So an odd thing started happening. I have a main dev workstation and a laptop I use to develop on too. Within a few hours of each other, they stopped loading Preform. Preform opens...
View ArticleKeep support contact points when thickening raft
@rkagerer wrote: I love that Preform now has the ability to Import supports when you load a model into a different resin environment or change print settings. Is it possible to do the same thing when...
View ArticleClik here to view.
Cleaning IPA with UV
@Dlefort wrote: I’ve been reading other posts about recycling IPA. People are filtering, distilling, using centrifugal separators. One thing people talked about ( and claimed success with) was hitting...
View ArticleNASA Outgassing Properties of High Temp
@Murdock_Hart wrote: Has anybody performed the NASA outgassing test on the high temp material? Are printed high temp resin parts UHV compatible? Posts: 1 Participants: 1 Read full topic
View ArticleForm 2 _actual_ print volume
@ToyForge wrote: In trying to print are large piece, it appears that Preform considers the print volume of the Form 2 to be 143.75mm x 143.75mm x 174.75mm. The advertised specifications indicate that...
View ArticlePreForm Minimum Height Above Base
@ToyForge wrote: The documentation for Advanced Support Structures indicates: Height Above Base This value indicates the minimum height of support structures - the smallest distance between the part...
View Article