Clik here to view.
Problem with build platform stuck in the air
@matildaschuman wrote: Hi, We have had several problems with our printer lately. I cleaned it throughly and did a successful test print a couple of weeks ago. Now when I started a new print, the build...
View ArticleClik here to view.
《汽车之友》杂志
@markzhang wrote: IMG_5437.JPG1920x1080 569 KB 缺什么零件就用3D打印出来！ Posts: 1 Participants: 1 Read full topic
View ArticleClear resin Resolution
@btdetermino wrote: Hi it seems that i have trouble printing with the clear resin as the prints always get broken halfway or do not print at at. I have tried cleaning the resin tank but i suspect that...
View ArticleClik here to view.
Out of memory when saving?
@mlabird wrote: I am printing this large owl and the file size is quite large. I would like to save it for I am going to be printing number of them. I do get this error that it ran out of memory? My...
View ArticleSwitch Reains in Same Tank
@Echoarms wrote: Id like to switch resins in my printer and have no interest in running black anymore. Can I reuse the resin tank for tough? Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Clear resin mold injected with liquid silicone rubber
@louiemendez wrote: These button pads I are made for a GPS faceplate. I’m very pleased with the bubble-free result. I will post more pics after they are painted and laser etched....
View ArticleForm 2 users help
@DenTheDentist wrote: Good day! I’m going to purchase Form 2 for my dental service. But I still have a doubts. Can someone print me my model from cast able resin and take a photo in a good resolution...
View ArticleError 51 Resin tank NaN °C
@Astratiformlab2 wrote: The Form 2 does not control temperature and the print can not start. Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Warhammer 40K Herald of Khorne Bloodletter
@Dudemeister wrote: Here is a print I did a about a month ago, but didn’t get a chnace to paint it until last night. This is a Warhammer 40K miniature sculpted by filipturz and posted on Thingiverse:...
View ArticleForm 2 / Clear V2 resin: Non-specific DNA capture? Biocompatibility?
@v_rao wrote: Hi folks! I’m using the From2 / Clear V2 resin to print microfluidic prototypes to isolate DNA from bacterial samples. DNA yield was poor on the 3D printed device compared to standard...
View ArticlePop up message on in PreForm when a Print is finished
@cubo wrote: Often I find myself looking into Preform to find out how much time is left to finish a print job. Since the calculated time is not exact and changes it would be good if Preform could POP...
View ArticleClik here to view.
Strange print failure
@tomer wrote: after a successful printing at the first time second printing come out “cut” - missing material at the middle of the printing see pic pls adivce should the resign still good for use? i...
View ArticleForm 2 cartridge mismatch after firmware update
@ClaudioPin wrote: Hey there, Yesterday my F2 started malfunctioning immediately after the firmware update (dated 20 Oct). After the update, touchscreen wasn’t working, so I needed to unplug the F2 in...
View ArticleLost detail and voids around the supports
@jmwright1058 wrote: I’ve been pretty successful at getting accuracy on the side opposite the supports, so I orient the part this way. However, I have detail on both sides, so it’s just not possible...
View ArticleUPS for Form2 for power outages
@geoff wrote: I’m looking for any information regarding power usage of the Form2 and what it would take to keep one running for 24-48 hours in the case of a power outage. Any ideas? Posts: 1...
View ArticleClik here to view.
Problem Whit Black v3 and form 2 ? Help!
@thekkiinngg wrote: Voir la photo la base deviens avec un contour très mince comme une feuille de papier de résine et c’est petit morceaux se repend partout dans la résine ??? Que faire , J,ais Black...
View ArticleClik here to view.
Print defect, orientation or other issue?
@cjryker06 wrote: I threw together this test print to try out a few things and the result was overall good. The odd part is what looks like a trail off the text tests. It is literally a line standing...
View Article"Continue in open mode" in case of sensor error message
@Konstantin_Dani wrote: So tired of the “sensor error” messages. Has to be an option to continue print with what’s left in the tank. Posts: 1 Participants: 1 Read full topic
View ArticleForm 1+ looking for a new home
@Jeffrey_dube wrote: Has 4 unopened resin trays all original packaging and a custom dust cover cleaning kit about 500 hours on it contact jeff nouveau@ameritech.net asking $1400 including shipping....
View ArticleHow tall is Form2 with cover open?
@Adin wrote: Making enclosure dont have machine yet. Thanks Posts: 2 Participants: 2 Read full topic
View Article